Vollrath F144 User Manual download pdf (Page 15)

Owner’s Manual #513677 9 F144I2, SF144I2 and SF121I2 Model Machines

B. Install the rear seal o-ring. Lubricate the outside

of the rear seal o-ring with sanitary lubricant.

NOTE

Do not put Petrol-Gel directly onto the auger shaft.

C. Lubricate the inside metal surface of the rear

seal and install it onto the auger shaft. DO NOT

lubricate the outside of the rear auger seal (Fig.

3-8).

D. Lubricate the hex drive end of the auger with a

small amount of spline lubricant. A small container

of spline lubricant is shipped with the machine.

E. Screw the springs onto the studs in the plastic

ﬂ ights. The springs must be screwed into the

ﬂ ights completely to provide proper compression.

NOTE

Make sure the rear of the freezing cylinder is clean

and dry before installing the auger shaft. If the

freezing cylinder is dirty or if there is moisture, the

freezing cylinder may leak at the rear seal.

F. Install the two plastic ﬂ ights onto the rear of the

auger and insert it part way into the freezing

cylinder.

G. Install the remaining plastic ﬂ ights, push the auger

into the freezing cylinder and rotate slowly until

the auger engages the drive shaft.

H. Apply a thin layer of sanitary lubricant to the inside

and outside of the auger support bushing. Install

the bushing onto the auger support and install the

auger support into the front of the auger. Rotate

the auger support so that one leg of the support

points straight up.

I. Apply a thin layer of sanitary lubricant to the

o-rings on the spigot body and install the spigot

body through the bottom of the front door.

K. Apply a thin ﬁ lm of sanitary lubricant to the door

seal o-ring and ﬁ t it into the groove on the rear

of the front door.

M. Place the front door assembly on the mounting

studs and the push front door against the machine

carefully.

N. Secure the front door to the machine by placing

the knobs on the studs and tightening until ﬁ nger

tight. Do not overtighten. A proper o-ring seal can

be observed through the transparent front door.

O. Thread the agitator onto the blender shaft and

install the clear acrylic splash guard.

3.8 SANITIZING

Sanitizing must be done after the machine is clean and

just before the machine is ﬁ lled with mix. Sanitizing the

night before is not effective. However, you should always

clean the machine and parts after using it.

NOTE

The United States Department of Agriculture and

the Food and Drug Administration require that all

cleaning and sanitizing solutions used with food

processing equipment be certiﬁ ed for this use.

When sanitizing the machine, refer to local sanitary regu-

lations for applicable codes and recommended sanitizing

products and procedures. The frequency of sanitizing

must comply with local health regulations. Mix sanitizer

according to manufacturer’s instructions to provide a 100

parts per million strength solution. Mix sanitizer in quanti-

ties of no less than 2 gallons of 90°F to 110°F (32°C to

43°C) water. Allow sanitizer to contact the surfaces to be

sanitized for 5 minutes. Any sanitizer must be used only

in accordance with the manufacturer’s instructions.

A. Prepare 2 gallons of Stera-Sheen sanitizing

solution following the manufacturer’s instructions.

B. Install the mix inlet regulator into the hopper with

the air tube towards the front of the machine.

NOTE

Do not twist the mix inlet regulator when installing.

Figure 3-9 Mix Inlet Regulator

Position Air

Tube Towards

Front of Machine

Figure 3-8 Lubricate Rear Seal

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 28 29

Comments to this Manuals

No comments

Vollrath F144 User Manual Page 15

Comments to this Manuals

Related products and manuals for Kitchen Vollrath F144